Aironet AP4500 Betriebsanweisung Seite 38
- Seite / 223
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installing the Bridge for Ethernet or Token Ring 1 - 9
Attaching the AC/DC Power Pack
and Powering On the Ethernet or Token Ring
Wireless Bridge
1. Insert the small plug on the end of the AC/DC power pack cord into
the power port.
2. Plug the AC/DC power pack into an electrical outlet.
(120VAC/60 Hz or 90-264VAC as appropriate)
3. Power on the Ethernet or Token Ring Wireless Bridge by pushing the
On/Off button.
When power is initially applied to the Ethernet or Token Ring Bridge,
all three indicators will flash in sequence to test the functionality of the
indicators.
Figure 1.7 - AC to DC Power Pack Connections and On/Off Button
On/Off Button
- Technical Reference Manual 1
- Contents 3
- Contents iii 5
- Contents v 7
- Contents vii 9
- Contents ix 11
- List of Figures 12
- List of Tables 13
- Typographical Conventions 16
- Protocols Supported 18
- Radio Characteristics 18
- Radio Ranges 19
- Site Survey 19
- Line of Site 20
- Radio Antenna 21
- Security Features 21
- Terminology 22
- Bridge System Configurations 23
- Part 1 - Getting Started 28
- CHAPTER 1 30
- Ethernet Token Ring 31
- Installation 32
- Ethernet cabling connections 35
- Wireless Bridge 38
- Top Panel Indicators 39
- Accessing the Console System 42
- Access Methods 43
- Using the Console 43
- Sub-Menus 44
- Commands and Information 45
- Are you sure [y/n] : 46
- Telnet Access 47
- Web Access 48
- About the Menus 50
- Enabling Linemode (Linemode) 55
- Monitoring of the DTR Signal 56
- Part 2 - Configuration 58
- Before You Begin 60
- Viewing the Configuration Menu 61
- Before You Begin 3 - 3 62
- Restoring your Configuration 63
- Configuring the Radio Network 64
- Establishing an SSID (SSID) 66
- Basic Rates (Basic_rates) 67
- Enabling Root Mode (Root) 67
- Using the Configuration Radio 68
- IEEE 802.11 Menu 68
- Encapsulation 70
- 90, Source received 90 74
- Setting Diversity (Diversity) 77
- Configuring the Ethernet or 80
- Token Ring Port 80
- Setting Network Identifiers 88
- Entering a Host Route (Host) 92
- Deleting a Route (Delete) 92
- Configuring SNMP 94
- Configuring SNMP 7 - 3 96
- Adding a Community (Add) 97
- Configuring SNMP 7 - 5 98
- Configuring SNMP 7 - 7 100
- CHAPTER 8 102
- Overview 103
- Bridge 1 Bridge 2 104
- How STP Protocol Works 105
- Determining the Spanning Tree 107
- Understanding Bridge Failures 107
- Avoiding Temporary Loops 107
- Establishing Timeouts 108
- Node Address Aging 108
- Implementing STP Protocol 109
- (Root Bridge Only) 110
- Rpriority) 116
- (Repeater Only) 118
- Viewing Statistics 122
- Viewing the Statistics Menu 123
- Viewing Statistics 9 - 3 124
- Error Statistics 126
- Token Ring Error Statistics 126
- Ethernet Error Statistics 128
- Viewing Statistics 9 - 9 130
- Viewing Statistics 9 - 11 132
- Viewing Statistics 9 - 13 134
- CHAPTER 10 136
- Using the Association Menu 138
- BRE105E 22ff0a 142
- Wired LAN 143
- Root Unit 143
- End Node A 143
- End Node B 143
- End Node C 143
- Using Filters 146
- Using the Filter Menu 147
- Displaying The Filters (Show) 148
- Removing a Filter (Remove) 149
- Using Filters 11 - 5 150
- Setting the Default (Source) 151
- Using Filters 11 - 7 152
- Using Filters 11 - 9 154
- Adding A Filter (Add) 156
- Using Filters 11 - 13 158
- Removing an Entry (Remove) 160
- Using Filters 11 - 17 162
- Setting Up Event Logs 164
- Error Logs 168
- Severe Error Logs 168
- Using the Logs Menu 172
- Performing Diagnostics 178
- Using the Diagnostics Menu 179
- Using the Network Menu 180
- Sending a Ping Packet (Ping) 182
- LAN Interfaces Supported 192
- Physical Specifications 193
- Console Port Pin-Out 194
- Ethernet Only 197
- Token Ring Only 197
- Appendix C - SNMP Variables 202
- C.1 MIB II Variables 202
- The System Group 202
- The Interfaces Group 203
- The IP Group 204
- The ICMP Group 205
- The UDP Group 205
- The Transmission Group 206
- The SNMP Group 207
- The Configure STP Group 208
- The Token Ring Group 210
- 3.2 The ARLAN Custom MIB 211
- The Configure Ethernet Group 211
- The Configure ARLAN Group 211
- The Configure Filtering Group 211
- The Configure Console Group 212
- The Configure SNMP Group 212
- The Configure Logs Group 213
- The Configure Ident Group 214
- The Logging Group 214
- The Admin Group 215
- The Admin LinkTest Group 215
- The Admin FTP Group 216
- User’s Guide 218
- Communications 218
- Web Site 218
Verwandte Produkte und Handbücher für Vernetzung Aironet AP4500
Vernetzung Aironet BR500 Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Vernetzung Aironet AP4500 Betriebsanweisung
(44 Seiten)
(44 Seiten)
Vernetzung Aironet BR2000-E Betriebsanweisung
(46 Seiten)
(46 Seiten)
Vernetzung Aironet BRE500 Betriebsanweisung
(47 Seiten)
(47 Seiten)
Vernetzung Aironet PCI4810B Betriebsanweisung
(84 Seiten)
(84 Seiten)
Vernetzung Aironet BR2000-E Betriebsanweisung
(180 Seiten)
(180 Seiten)
Vernetzung Aironet BR500 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung Aironet PC4800B Betriebsanweisung
(15 Seiten)
(15 Seiten)
Vernetzung Aironet AP2200-E Betriebsanweisung
(20 Seiten)
(20 Seiten)
Vernetzung Aironet AP4500 Betriebsanweisung
(150 Seiten)
(150 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern